Home > Dual Channel > Dual Channel Setup And Audio Trouble

Dual Channel Setup And Audio Trouble

This is where I get tripped up.. The AppleTV, for example, supports AC3 but not DTS. Add: Adds a new channel configuration to the Configurations list. Check all boxes for it. Source

Most of these DSP modes, unless otherwise specified, do not make use of the back channels. The reset process may take up to 5 minutes to complete. To reenable it, follow the instructions above. In a surround sound setup, you can assign a mono channel to any surround channel.

So I could have the preamp plugged in via USB to both PCs and avoid getting a mixer? Restart QuickTV and see if it plays normally. One or more of the other numbers may also be needed, though it will vary by provider. But now that I think of it, I'm wondering if this is possible because the HDMI would be coming out of my GPU, and I don't think GPU's have anything to

On Windows you will have two entries for each device, one DirectSound and one WSAPI; these are two different Windows APIs. If the card information is still missing and you have verified that the card is inserted correctly, try another CableCARD. 161-0 message displayed in logs Back to top The logs may For listening to the audio from your Streaming PC on your Gaming PC, your going to need an additional 3.5mm cable from the Streaming PC to your Gaming PC. Check your speaker cables Check your cables to make sure they are all properly connected to your speakers and your amplifier/receiver.

Select QAM256 for the modulation and click Next. All rights reserved. Reopen Windows Media Center and access the TV setup wizard again. If the LED is blinking red (HDTC-2US) or solid red (other devices), this indicates that the device does not have a network connection.

Troubleshooting: Still having problems? Make sure that your HDHomeRun is connected in such a way that it has internet access. HDHomeRun Setup - Discovery Error 4001 Back to top This indicates that there is a hardware issue with your device. In the case of Comcast, this is not something that can be performed by a phone representative.

  1. For more information, see Share roles as files.
  2. If only one tuner shows the program that is visible on both TVs, you are sharing a tuner.
  3. Please start a New Thread if you're having a similar issue.View our Welcome Guide to learn how to use this site.
  4. No call-outs or witch-hunt attempts.
  5. You may need 2 repeaters, (not sure on this) set the input to the NVIDIA High Definition Audio and then repeat it to an output.
  6. Click on one of the channels you just added.
  7. Click Save.
  8. To add multi-language audio channels Figure 116: Multi-language audio setup Click the Add button.
  9. In the Part II we will focus solely on video.
  10. If the device you are accessing from is using a wireless connection, try a wired connection.

Click Save. https://support.plex.tv/hc/en-us/articles/201214687-Audio-Configuration-Guide-Plex-Home-Theater We are working on updates to better handle HD channel playback. Click Save. by ahtoi / April 22, 2010 5:25 PM PDT In reply to: Understanding dual channel memory http://en.wikipedia.org/wiki/Dual-channel_architectureBut the link can explain a lot better then I can.

A few days later I stopped by for a family barbeque and sat down for a little listen. this contact form Go to the other room Go to the other room which is experiencing the problem. Check to make sure that signal is present on the cable line you are using. Verify that the HDHomeRun Service is not Disabled, and is Started.

This site is completely free -- paid for by advertisers and donations. If you have any type of remote access software on the PC such as TeamViewer, VNC, Remote Administrator, GoToMyPC, PCAnywhere, or LogMeIn, these programs may intercept the video data, breaking the Some but not all expected channels are found in a scan Back to top Go to the web page for your HDHomeRun device (click on one of the tuner numbers on http://webtrekkie.com/dual-channel/dual-channel-ram-in-single-channel-mobo.php Probably have to get another mic haha...

Loading... It handles at most 6 channels (5.1) and is supported natively by almost anything. Aliases are separated by a semicolon.

Use a 0 after the .

If you mouse over the different sources, it will show you at the bottom the channel number it is on. It is backwards compatible with DTS. Let's be grown ups. If not, or if it fails to turn on multiple times, please open a trouble ticket so we can replace it.

To manually activate an audio device Open the configuration file. This is the number listed in the Tune column in HDHomeRun Setup. Overtime, the connectors that bypass this feature can oxidize or corrode which leads to a faulty connection. Check This Out I don't use VAC, but the basics should be the same.

Never treat them as a biblical source but more as a starting point. To complicate matters further, you must also engage your DVD/Blu-ray player set-up menu to ensure the toslink/HDMI output is set for multi channel bitstream. If you are not using RCA cables, continue with the next step. For HDHomeRun PRIME, make sure that you are running a firmware version of 20130328 or newer and that you have completed a channel scan in HDHomeRun Setup.

On Windows, try both 32 and 64 bit versions. Make sure that you are running a recent firmware version on your HDHomeRun. Advanced users may also wish to check each interconnect individually with a multimeter to ensure they are not defective. I'll fill this thing up in the morning, canĀ“t make the noise of opening my case to check the PSU specs right now.

Activate the identified audio device (Available0) by adding its name to the AudioDevice0 setting. If you are using a Cisco CableCARD, the host ID number must be entered into the cable provider's system.