Dual Boot With 2000 And 98
Then Debug creates a new C:\BOOTSECT.DOS file. Diese Funktion ist zurzeit nicht verfügbar. And Fdisk may prove difficult! Copy the bootsect.f32 file to a 3.5" disk. Source
This is C:\. 2. Wird geladen... This time run Btsect.bat from Win9x boot disk when at Step 3.1 [top of page] UPGRADE WINDOWS 9X IN A DUAL-BOOT Upgrading Win9x in a Dual-Boot with XP/2K/NT should Not be How many new PCs that have Win98 preinstalled support this assumption? http://www.duxcw.com/digest/Howto/software/windows/dual/
The Rescue Boot disk will always boot XP/2K/NT for you in any event. You need the full installation or setup version to install a Windows. The Format method produces a fresh and clean system, and is essential in serious degradation or if a virus is suspected. Using SYS C:, or FDISK /MBR, from the Win9x boot disk. 2.
- Boot to Win 9X. 5.
- In my case, I use 2 GB NTFS partitions for each.
- Uninstalling the upgrade may delete Boot.ini.
- Make your own Bootsect.dos: (read the Bootsect.dos created new page) Use this only if Win9x is installed on C: (active partition), and Win9x boots normally without a menu (though you
- Some settings, not used here, are very advanced.
Scott Gaulke Log In or Register to post comments Will Johansson (not verified) on Dec 1, 1999 Heres an easy way to get NT on Fat16 while Windows 98 on Fat32.. On large hard drives I just partition them to the limit for a FAT16 partition and do the same thing over. Obviously Win9x can not boot without it. Restore Points and Windows XP While not essential, it's best practice to apply a fix to prevent Windows XP removing Restore Points created by Win7. [top of page] Make a Partition
But, if necessary, proceed as follows. In Enter the amount of space to shrink in MB: enter enough for Win98/Me, 2K and XP. (make sure the Win98 and 2K partitions start before the 127 GB limit for installation if Win9x is installed first. check these guys out Anmelden 2 Wird geladen...
One thing, is that to boot in Windows NT, you have to choose the Windows 2000 selection or the good ol' Windows NT line. First check if FAT or FAT32 is used for the PC system partition (C:) and OS boot partition (if different). Log In or Register to post comments Rolando (not verified) on Nov 24, 1999 Thanks for this great article. Even Microsoft doesnt seem to know there is such a simple way to create a BOOTSECT.DOS file!
Important Installation Notes Full Installation CD/DVDs. http://windowsitpro.com/windows/dual-booting-windows-nt-40-and-windows-98 If your computer is configured to dual-boot to either Windows XP or Windows 2000, the process to boot to the other operating system can be slow. Proceed at your own risk. 3. Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar.
this is an excellent solution with having to purchase additional software. http://webtrekkie.com/dual-boot/dual-boot-xp-pro-2000.php Once the two partitions have been installed on the computer and Windows 95/98 is installed onto one of those partitions, boot to an MS-DOS prompt, loading the CD-ROM drivers (Windows bootable Melde dich bei YouTube an, damit dein Feedback gezählt wird. Uninstalling Win Me in a Dual-Boot: Never 'Uninstall' Win Me from a dual-boot.
However, since all the x64 cpu's support x86 as well, you can dual-boot Win98/Me on a 64-bit computer provided you execute an extra few cold boots while the Win98/Me installation tries Dual-Boot Blues You might need to run two Windows OSs until more hardware and software supports Win2K. Hidden Active Partition. have a peek here How to Dual Boot Windows 98 and Windows NT 4.0 with Large FAT16 or NTFS Volumes Microsoft Knowledge Base Article: 243896 This article describes how to dual boot between Windows NT
Multiple-boot configurations with Windows NT and Windows 95, etc. The products referenced in this site are provided by parties other than LabMice.net. If Shrink does not give you sufficient Unallocated space, read how to Shrink the Windows 8, 7 or Windows Vista Partition for instructions or use the free GParted Live CD.
All rights reserved.
Dual boot Windows 95 with Windows ME Windows ME will detect if any Windows operating system already exists on the computer before the installation, so it is important that you create This is also where a Win9x/Me boot partition rests most comfortably and it must be FAT/FAT32. Log In or Register to post comments Please Log In or Register to post comments. Some settings, not used here, are very advanced.
EasyBCD. It's helpful at times, but is to be avoided if possible. [top of page] (b) DELETE & REINSTALL Delete the Windows 9x folders/files and reinstall as previously without a format. In the General tab, enter wn_7 as the label for the Windows 7 volume, and click Apply. Check This Out Then return here.
Right-click your CD/DVD drive(s), select Change drive letter and paths..., and click Change.